Related topics

Improving Cable signal on PC Tv tuner card
Secondly, the signal levels are extremely wide -- with both high power UHF TV interference and other VHF/UHF signals that screw up the UHF HDTV signal to some If my setup was supplying only one HDTV tuner, and I didn't mind changing the antenna position for each channel (even within the same antenna farm),

Digital TV - Cheap set-top boxes.
Just installed a Hauppauge WinTV tuner card (under XP, ASUS A7V266EX MB, Athlon XP 1700+). Other cards in the system are AGP Video, 10/100 ethernet and an Adaptec SCSI card Reception OTA to the TV is excellent - no ghosting, strong signal etc. However that same signal to the TV tuner card is lousy with noise bars,

Signal Degradation From Signal Splitters??? - LONG REPLY
I'd like to split this line just before the modem and have: Splitter 2 - Output 1 to Modem, Output 2 to Tuner. What can I do to keep signal strength up? I also plan to install a switch to run my internet to a second computer. Thanks, Jesse The 2-way splitter installed by my cable company (since I have both cable TV

Scart modification to soften the signal ?
Can you tell me which TV tuner is in that box. I'm pretty sure it's an Avermedia tuner (not sure of the model though). It may simply be a bad driver that sees the Can any other Gateway 610 owners out there try to setup their TV signal source as cable/no set top box and then see if you can tune to channel 2.

TV RF transmitter
"big_john_bc" wrote: Hi everyone, I'm running Vista home premium with a ATI Theater 550 pro tuner. The tv cable run to my vcr then cables to the tuner. The problem is that I COULD record manually before with no problem and then got the occassional "No tv signal" error message then got the message All the time.

TV Tuner card for a PC
In THAT situation adding a masthead amp can help by putting a much better TV signal into the cable system, substantially higher than the PC interference getting into the coax thru No indication of snow in the picture has been given so we can assume that the wanted RF input level to the tuner is satisfactory.

Loss of signal MCE 2005
Matt Ackeret matt...@vax.hanford.org alt video ptv tivo In article <BC96FF08.32A%ak2j...@excite.com>, jack ak <ak2j...@excite.com> wrote: Standby will connect the Tivo's RF input to RF output and if there is an antenna or cable signal available at the RF input connector, the TV tuner can be used to select channels

UHF reception on VCR and audio encoding of mono VCR
If the unit is in a really dusty place or if people smoke heavily in the home, the RF switch is possibly dirty and needs to be cleaned with TV tuner cleaner. Hope this info helps. Try not to miss a step. if you do miss a step in the chain of the signal processing, the end result will not be achieved.

Zaąto imam slab signal na tv tuneru? V-GEAR DV ProTV ...
I would guess the RF output on the box is mono - it's not passing an MTS signal for any stations. This could be caused by the box or the way the cable system provides the signal. So, using the box with the VCR or TV tuner switched in to get the RF output on the VHF channel output by the box (normally on chs.

Gadget Toys - Cable TV for free ?
Can you watch the Foxtel signal via co-ax on the TV tuner, or via the VCR tuner? Now the fun part - problems: PROBLEM 1. I can not tune my TV to VCR via channel - I can only access it via TV/VCR button on TV remote. I tried to follow the instructions in the User's Guide - it did not work: Set TV to channel 38.

Splitting a cable for Modem and TV - How?
Well... it probably _could_, IF the PC had _direct_ access to the full, _raw_ video signal coming in. Unfortunately, the PC does NOT have access to the raw signal when using a TV-on-the-desktop card like the ATI All-In-Wonder or similar products. The ATI card contains an analog TV-tuner front end, just like the

HELP! Reception of Audio TV signal
bassett bass...@bassettskennell.com aus tv digital Regardless of what you might think 95% of transmissions entering the TV tuner are analogue... Bassett steps back to avoid the Bluster and Blast. You might well have a digital set-top box to decode the digital terrestrial signal, But it converts to analogue,

Setting TV signal
This involves de-interlacing and stretching of the scan lines ... which causes the blur and grain that appear when you view a TV signal on a monitor. Different TV tuner cards do different tricks to clean up this "noise" ... but you are correct that none of them do it perfectly. Bottom line, some of the noise that

Why is the picture from TV tuner cards so poor?
I posted the question before about poor TV tuner picture quality (lots of interference, horizontal and vertical wobbly lines, fuzz, and so on) that is good on some stations, and unwatchable on 2/3 of the cable stations. It changes very much from station to station. I've attached a sample of poor quality picture,

Is anybody emulating Cable-TV descramblers ?
It is actually possible to calculate the limits from the signal specifications, and it has indeed been done: For PAL, the maximum resolution is 576 scanlines and TV tuner cards usually give uncompressed images, but then again the bitrate is so high that you really can't do anything reasonable with them in full

ReplayTV High Quality MPEG2 -> SVCD; NO Transcoding Required!!!
I can already watch My Videos, My pics and My music but I can not set the TV signal. I have an Avermedia AverTV DVB-T USB2.0 card that says windows MCE compatible. The TV tuner works great on my computer but when I tried to find TV services on the windows media center (in my PC) no services are found and get the

TV, VCR, Satellite System, & TV Stand
First, you're counting on the modulator to do a decent frequency shift of the IF signal to channel 3/4/whatever. I wouldn't bet on a cheap modulator doing a very good job. The second problem is that you are then counting on your TV's tuner to do a good job tuning in the signal and converting it back to an IF signal

Need Channel 73 to Set Up TV Signal
The idea is this: I have two cable-type Tv output devices, one is set to output to channel 3, and the other to channel 4. I have one tv cable input to a pc tv tuner card, but I can select channel 3 or channel 4 via the software for the tv tuner card (ATI's TVWonder). If I just use a "Y" cable connector,

Do they make this? (Cecil)
PCM is recorded as video signal on the video track. One thing PCM does not like is the drop-out compensator, and by switching your SL-HF400's MPX filter switch to As for the input select, selecting tuner will give you TV tuner. The line/audio will have the VTR recording from the back panel video/audio inputs

Any reason for Direct TV customers not to go for the "deal" ???
The usual transistorized tuner doesn't have any ICs, just a few transistors and diodes, and a lot of tuned circuits. The ICs that control the voltage for the varicaps are usually located outboard of the actual tuner. Perhaps you should read up on the block diagrams for TV, so you can get an idea of what signal